Full Freeview on the Rosneath (Argyll and Bute, Scotland) transmitter
|Google Streetview||Google map||Bing map||Google Earth||55.991,-4.794 or 55°59'28"N 4°47'40"W||G84 0LF|
The symbol shows the location of the Rosneath (Argyll and Bute, Scotland) transmitter which serves 41,000 homes. The bright green areas shown where the signal from this transmitter is strong, dark green areas are poorer signals. Those parts shown in yellow may have interference on the same frequency from other masts.
This transmitter has no current reported problemsThe BBC and Digital UK report there are no faults or engineering work on the Rosneath (Argyll and Bute, Scotland) transmitter.
Which Freeview channels does the Rosneath transmitter broadcast?If you have any kind of Freeview fault, follow this Freeview reset procedure first.
Digital television services are broadcast on a multiplexes (or Mux) where many stations occupy a single broadcast frequency, as shown below.
64QAM 8K 2/3 24.1Mb/s DVB-T MPEG2
DTG-6 256QAM 32KE 2/3 40.2Mb/s DVB-T2 MPEG4
DTG-8 64QAM 8K 3/4 27.1Mb/s DVB-T MPEG2
H/V: aerial position (horizontal or vertical)
Are you trying to watch these 11 Freeview HD channels?
The Rosneath (Argyll and Bute, Scotland) mast is not one of the extended Freeview HD (COM7 and COM8) transmitters, it does not provide these high definition (HD) channels: BBC Four HD, BBC News HD, CBeebies HD, Forces TV, FreeSports, More4 +1, Now 70s, PBS America +1, That's TV , Quest Red +1, RT HD.
If you want to watch these HD channels, either use Freesat HD, or move your TV aerial must point to one of the 30 Full Freeview HD transmitters. For more information see the want to know which transmitters will carry extra Freeview HD? page.
Which BBC and ITV regional news can I watch from the Rosneath transmitter?
BBC Reporting Scotland 2.4m homes 9.2%
from Glasgow G51 1DA, 35km east-southeast (117°)
to BBC Scotland region - 230 masts.
How will the Rosneath (Argyll and Bute, Scotland) transmission frequencies change over time?
|1968-80s||1984-97||1997-98||1998-2011||2011-13||2013-18||2013-17||5 Sep 2018|
|VHF||C/D E||C/D E||C/D E||C/D E||C/D E T||C/D E T||W T|
tv_off Being removed from Freeview (for 5G use) after November 2020 - more
Table shows multiplexes names see this article;
green background for transmission frequencies
Notes: + and - denote 166kHz offset; aerial group are shown as A B C/D E K W T
waves denotes analogue; digital switchover was 11 May 11 and 25 May 11.
How do the old analogue and currrent digital signal levels compare?
|COM4||, COM5||, COM6||, PSB1||, PSB2||, PSB3||||(-7dB) 2kW|
|Mux 1*, Mux 2*, Mux B*, Mux C*, Mux D*||(-17dB) 200W|
|Mux A*||(-20dB) 100W|
|COM4≡, COM5≡, COM6≡, PSB1≡, PSB2≡, PSB3≡||(-31dB) 8W|
Which companies have run the Channel 3 services in the Rosneath transmitter area
Is the transmitter output the same in all directions?Radiation patterns withheld
The simple answer is yes, possibly. However, I can't find any reports of any current or recent faults at Rosneath by the BBC or Freeview and it hasn't been recently listed for Planned Engineering.
Depending on your location, you might be able to receive other transmitters and if you retuned at all if there was any brief interuption due to weather conditions etc., you might have inadvertently got tuned to the wrong transmitter. Check in your TV's tuning section that you are tuned to the UHF channels listed at the very top of the page. Those in the 5 Sep 2018 listing lower down are not up-to-date.
If you are correctly tuned, check that your downlead looks undamaged and that your aerial seems intact and pointing in the correct direction. Also check all you coax plugs, connections, flyleads etc, unplug connectors check for corrosion or other problems and reconnect them. Flyleads can be a common problem, try swapping them. See what signal strengths (if any) and quality you are getting for the multiplexes shown in your TV's tuning section, this might indicate potential issues with your aerial or downlead.
Aerial mis-alignments, problematic connections, water ingress etc. can seem to affect reception of just AN individual or several multiplexes.
If you've altered anything around in your installation, check that you don't have any HDMI leads close to any aerial or flyleads, especially if the aerial and flyleads aren't high quality double screened types. HDMI is known to sometimes cause interference.
|link to this comment|